- Kinetic theory: assumptions of the model
- Direct and inverse proportion · coming soon
- Pressure in liquids · coming soon
Does doubling the temperature double the pressure?
A sealed steel can of air sits at 10 °C. You warm it to 20 °C. The temperature number has doubled. Has the pressure inside doubled?
Most people's first answer is yes. It is wrong: the pressure rises by only about 3.5%. And cooling the can from 10 °C to −10 °C changes the sign of the temperature, but the pressure certainly does not become negative. Something about the Celsius scale is wrong for gases. By the end of this lecture you will know exactly what, and you will have found the coldest temperature there can be.
The last lecture made two predictions from the kinetic model. Squash a gas into a smaller space, and each molecule reaches a wall more often, so the pressure rises. Heat a gas, and its molecules move faster, so they hit the walls harder and more often, and again the pressure rises. It promised to turn these two ideas into laws with numbers. Here they are.
A gas sample has four quantities: pressure , volume , temperature and amount. Here the amount is always fixed: no gas leaks in or out. That leaves three quantities. Hold one still, and watch how the other two are linked. There are three ways to do that, and each gives one law.
Squeeze it: Boyle's law
Trap air in a syringe, block the end, and push the plunger in slowly, so the air stays at room temperature. Measure them carefully and you find a simple pattern. Halve the volume, and the pressure doubles. Divide the volume by three, and the pressure triples.
The kinetic model explains why. At a fixed temperature the molecules keep the same typical speed, so each hit on a wall gives the same push. Halve the volume, and there are twice as many molecules in each cubic centimetre. So twice as many molecules hit each square centimetre of wall every second, and the pressure doubles.
For a fixed amount of gas at a constant temperature, the pressure is inversely proportional to the volume:
, so
"Inversely proportional" means that when one quantity is multiplied by a number, the other is divided by it, so their product never changes. The graph is a curve, not a straight line.
The law is named after Robert Boyle. In 1662, working in Oxford with his assistant Robert Hooke, he trapped air in the short sealed arm of a J-shaped glass tube and poured mercury into the long arm. As he added mercury, he recorded the trapped air's volume beside its pressure. He published the two columns of numbers and invited readers to compare them. In France it is often called Mariotte's law.
Heat it in a closed box: the pressure law
Now hold the volume fixed. Seal air in a rigid flask with a pressure gauge, and heat it in a water bath. The pressure rises steadily. Plot pressure against temperature in degrees Celsius, and you get a straight line. But the line does not pass through zero. At 0 °C the air still has plenty of pressure.
So pressure is not proportional to the Celsius temperature. That is why doubling 10 °C to 20 °C did not double the pressure. But follow the straight line backwards, to lower and lower temperatures. It reaches zero pressure at about −273 °C. Every gas you try gives a line that ends at that same temperature.
This suggests a better place to start counting temperature. Measure temperature from −273 °C instead of from 0 °C. That is the kelvin scale, which you met in the last lecture: in kelvin is in °C plus 273. On this scale, the pressure line passes straight through zero, so pressure is proportional to the kelvin temperature.
For a fixed amount of gas at a constant volume, the pressure is proportional to the temperature in kelvin:
, so
Many books call this Gay-Lussac's law. But the French physicist Guillaume Amontons had found a steady link between the temperature and pressure of air in a closed vessel around 1700. That was a century before Gay-Lussac, so other books name the law after Amontons.
The kinetic reason is the second prediction from the last lecture. Heating makes the molecules move faster. A faster molecule hits a wall harder, and it also crosses the box sooner, so it hits more often. Both effects push the pressure up. The last lecture showed that the average kinetic energy is proportional to the kelvin temperature, not the Celsius one. That is why kelvin, and not Celsius, appears in the law.
Go back to the sealed can. By what factor does its pressure really rise when it is warmed from 10 °C to 20 °C? What would you need to do to double the pressure?
Show the answer
Change to kelvin first: 10 °C is 283 K and 20 °C is 293 K. The pressure rises by the factor , about 3.5%, not 2. To double the pressure you must double the kelvin temperature, from 283 K to 566 K, which is 293 °C. The Celsius zero is not the point of no motion, so Celsius ratios mean nothing.
Heat it and let it grow: Charles's law
The third choice is to hold the pressure fixed and let the volume change. Trap some air in a tube behind a bead of liquid that can slide freely. The air always pushes on the bead with the pressure of the room, so its pressure stays constant. Heat the air, and the bead slides out as the air expands.
Plot volume against Celsius temperature, and again you get a straight line that misses zero. Try it below with three samples of different sizes.
Measure each sample: its volume is recorded at 0, 25, 50, 75 and 100 °C, at constant pressure. Then extend the lines backwards, and finally switch the temperature axis to kelvin.
This graph shows three samples of gas at constant pressure, with volumes of 1, 2 and 3 L at 0 °C. Their volumes were measured from 0 °C to 100 °C (solid lines), and the lines are extended backwards (dashed).
| Sample | V at 0 °C (273 K) | V at 100 °C (373 K) | V ÷ T |
|---|---|---|---|
| A | 1.00 L | 1.37 L | 0.003 66 L/K |
| B | 2.00 L | 2.73 L | 0.007 32 L/K |
| C | 3.00 L | 4.10 L | 0.010 98 L/K |
For each sample, V ÷ T is the same at 273 K and at 373 K, so V is proportional to the kelvin temperature.
You should have seen something remarkable. The three samples have different sizes, so their lines have different slopes. Yet every line reaches zero volume at the same temperature, about −273 °C. When you switched to kelvin, every line passed through the origin, and stayed the same for each sample.
For a fixed amount of gas at a constant pressure, the volume is proportional to the temperature in kelvin:
, so
The kinetic reason needs one more step than before. Heating makes each hit on the wall harder. If nothing else changed, the pressure would rise. For the pressure to stay the same, the hits must become less frequent. The gas manages this by spreading into a larger volume, so the molecules have further to travel between the walls.
The French scientist Jacques Charles found this behaviour in the 1780s but did not publish it. Joseph Louis Gay-Lussac measured it carefully for several gases and published it in 1802, giving Charles the credit.
The coldest temperature there can be
The point where all the lines meet is called absolute zero. Its modern value is −273.15 °C, which is 0 K. For calculations at this level, adding 273 is accurate enough.
Be careful about what the lines say. No real gas reaches zero volume. Long before −273 °C, every real gas turns into a liquid, and the straight lines stop. The dashed parts are an extrapolation of the model. But the model's meaning is clear. In an ideal gas, the average kinetic energy of the molecules is proportional to the kelvin temperature, so at 0 K it would reach its lowest possible value. Nothing can be colder than that.
The kelvin scale is named after William Thomson, later Lord Kelvin. In 1848 he proposed an absolute temperature scale based on the theory of heat engines, so that it would not depend on the properties of any one substance. He noted that the air thermometers of his day pointed to the same limit, about −273 °C. So the gas laws did not create his scale, but they agreed with it.
All three in one: the combined gas law
What if all three quantities change at once? Take the gas from to in two stages, using one law in each.
Stage 1: keep the temperature at and change the pressure from to . By Boyle's law, the volume becomes .
Stage 2: keep the pressure at and change the temperature from to . By Charles's law, .
Put the first result into the second. This gives . Multiply both sides by , and the combined law appears:
For a fixed amount of gas: , so
must be in kelvin. can be in any unit and in any unit, as long as each is the same on both sides.
That is it. That is the whole idea. Each of the three laws is this one equation with one quantity held still. Hold still, and the s cancel to leave Boyle's law. Hold still, and you get Charles's law. Hold still, and you get the pressure law. Learn this one, and cross out whatever stays the same.
The pressure must be the absolute pressure: the full push of the gas, measured from a perfect vacuum. Many gauges, such as tyre gauges, read the gauge pressure instead: how much the pressure is above the pressure of the atmosphere. Absolute pressure = gauge pressure + atmospheric pressure. A flat tyre reads zero, but its air still presses at about 100 kPa.
Before you calculate, decide which law applies. Sort these by what stays constant.
In each situation the amount of gas is fixed. Choose a card, then choose the law that describes it. Read the reason after each choice.
Each situation is sorted by the quantity that stays constant.
| Situation | Law | What stays constant |
|---|---|---|
| A diver's breath expands as she rises | Boyle | Temperature (the water barely changes) |
| A bicycle pump is pushed in slowly | Boyle | Temperature (slow, so it stays at room temperature) |
| A bubble rises through a cold lake | Boyle | Temperature |
| A sealed can is left in a hot car | Pressure law | Volume (a rigid can) |
| Car tyres warm up on a long drive | Pressure law | Volume (very nearly) |
| A balloon shrinks in a freezer | Charles | Pressure (a soft balloon matches the air around it) |
| Air in a tube behind a sliding bead is heated | Charles | Pressure (the bead keeps it at room pressure) |
| A weather balloon climbs into thin, cold air | Combined law | Nothing: p, V and T all change |
Worked examples
A diver at a depth of 20 m fills her lungs with 3.0 L of air from her tank. The absolute pressure there is about 300 kPa. If she held her breath and rose to the surface, where the pressure is about 100 kPa, what volume would the air try to take up? Assume the temperature stays the same.
Think first. The temperature is constant and the amount of air is fixed, so this is Boyle's law. The pressure falls to a third, so the volume should triple.
Her lungs cannot hold 9 L of air. This is why divers are trained to breathe out steadily as they rise and never to hold their breath.
Check. and . ✓ The pressure fell, so the volume rose, as it must.
A gas occupies 2.0 L at 100 kPa and 27 °C. What volume does it occupy at 200 kPa and 127 °C?
Think first. Convert to kelvin first: K and K. Then rearrange the combined law for .
Check. Doubling the pressure alone would halve the volume to 1.0 L. Raising the kelvin temperature by a third makes it a third bigger again, to about 1.33 L. ✓ With Celsius by mistake, the temperature ratio would be , and the answer would be about 4.7 L, far too big.
A tyre is pumped to a gauge pressure of 220 kPa at 15 °C. After a long drive the air in it is at 40 °C. Atmospheric pressure is 100 kPa. Assume the tyre's volume does not change. Find the new gauge pressure.
Think first. The volume is fixed, so use the pressure law. But the law needs absolute pressure, so add the atmosphere first, and take it away again at the end.
Absolute pressure before: kPa. Temperatures: K and K.
New gauge pressure: kPa.
Check. The absolute pressure rose by about 8.7%, the same factor as the kelvin temperature, . ✓ The gauge reading rose by about 12.6%, from 220 to 248 kPa, because the atmosphere's 100 kPa did not change. This is why tyre pressures should be checked when the tyres are cold.
A weather balloon is filled with 3.0 m³ of helium at sea level, where the pressure is 101.3 kPa and the temperature is 15 °C. It rises to 20 km. In the International Standard Atmosphere, the model used in aviation, the air there is at 5.47 kPa and −56.5 °C. Estimate the balloon's volume at 20 km. Assume its thin skin keeps the helium at the same pressure and temperature as the air outside.
Think first. All three quantities change, so use the combined law. In kelvin: K and K. (Here the data are precise, so use 273.15.)
Check. The pressure falls to about of its value, which alone would make the balloon about 18.5 times bigger. The cold makes it about a quarter smaller than that. So about 14 times its starting volume is sensible. ✓
Three traps
Every gas law that contains needs kelvin. Celsius ratios are meaningless: 20 °C is not "twice as hot" as 10 °C. Convert every temperature to kelvin before you substitute anything.
A tyre gauge reads the pressure above the atmosphere. The gas laws need absolute pressure. Add atmospheric pressure before using a law, and subtract it at the end if the question asks for a gauge reading.
Every law in this lecture is for a fixed amount of gas. If you pump more air into a tyre, or gas leaks out of a balloon, changes. The next lecture adds the amount of gas to the equation.
Work each one on paper first. Open a hint only when you are stuck.
-
The end of a bicycle pump is blocked. It holds 300 cm³ of air at 100 kPa. The handle is pushed in slowly until the air takes up 75 cm³. What is the pressure now? Why does the question say "slowly"?
Hint 1
Which quantity stays constant if the push is slow?
Hint 2
.
Full answer
Boyle's law: kPa. The volume fell to a quarter, so the pressure rose four times. "Slowly" means the air has time to stay at room temperature. A fast push warms the air, which you can feel at the end of a pump, and then Boyle's law alone does not apply. Check: . ✓
-
A balloon holds 500 cm³ of air at 20 °C. It is warmed to 80 °C at constant pressure. (a) Find its new volume. (b) At what temperature, in °C, would its volume be twice the starting volume?
Hint 1
Change both temperatures to kelvin.
Hint 2
(b) Doubling V means doubling the kelvin temperature.
Full answer
(a) cm³. (b) Twice 293 K is 586 K, which is °C, not 40 °C. Check (a): the kelvin temperature rose by about 20%, and so did the volume. ✓
-
An aerosol can contains gas at 300 kPa at 20 °C. Its label warns that it may burst above 1000 kPa. (a) What would the pressure be if the can were thrown into a fire at 600 °C? (b) Above what temperature would it reach 1000 kPa? Assume the volume of gas is fixed.
Hint 1
A rigid can: use the pressure law, in kelvin.
Hint 2
(b) , then convert back to °C.
Full answer
(a) kPa. (b) K, which is about 704 °C. In a real can the liquid inside also turns to gas as it heats, which raises the pressure much faster, so cans can burst at far lower temperatures. That is why the warning says never to burn them. Check (a): the kelvin temperature tripled, nearly, and so did the pressure. ✓
-
A stretch. A gas thermometer keeps a fixed volume of gas and reads its pressure. In one test it reads 100.0 kPa in melting ice (0 °C) and 136.6 kPa in boiling water (100 °C). Assume the pressure changes in a straight line with temperature. (a) At what Celsius temperature would the pressure fall to zero? (b) What does this tell you, and why is the true value a little different?
Hint 1
Find how much the pressure rises for each degree.
Hint 2
The pressure must fall by 100.0 kPa from 0 °C. How many degrees does that take?
Full answer
(a) The pressure rises 36.6 kPa over 100 °C, which is 0.366 kPa per degree. To fall 100.0 kPa from 0 °C takes degrees, so zero pressure would be at about −273.2 °C. (b) It locates absolute zero from just two measurements. Kelvin used the same number in 1848: a gas expanding by 0.366 of its volume between 0 °C and 100 °C. The modern value is −273.15 °C. The small difference comes from rounding the readings and from the gas not being perfectly ideal. Check: kPa. ✓
Several experimenters, over more than a century, each found one piece of the same pattern. Put together, the pieces say that stays fixed for any fixed amount of gas. And the pattern pointed to something nobody had looked for: a lowest possible temperature, the same for every gas. The kinetic model explains why: kelvin temperature measures molecular motion, so the scale has a bottom.
One question is left. The constant in is different for different samples: sample C in the graph builder had three times the constant of sample A, because it had three times as much gas. The next lecture brings in the amount of gas, in moles, and turns the combined law into one equation for every gas: .
- For a fixed amount of gas at constant temperature, is constant (Boyle's law), because a smaller volume means more hits on each part of the wall every second.
- For a fixed amount of gas at constant volume, is constant (the pressure law), and at constant pressure, is constant (Charles's law), with in kelvin.
- Extending any gas's pressure or volume line backwards reaches zero at the same temperature, absolute zero, −273.15 °C or 0 K.
- The three laws combine into , and each law is this equation with one quantity held constant.
- The gas laws need absolute pressure and kelvin temperature: add atmospheric pressure to a gauge reading, and add 273 to a Celsius temperature.