- Physical quantities and units
- Ordering and rounding decimals · coming soon
- Dividing decimals · coming soon
- Errors in measurement
- Recording and processing data · coming soon
- Weight and mass · coming soon
A coin that will not sit still
Take a coin and a ruler, and measure the coin's diameter: the distance straight across it, through the middle. It sounds like a five-second job. Try it, and three problems appear at once.
The coin is round, so it is hard to see exactly where its edge touches the scale. It may roll. And where exactly is "straight across, through the middle"? Measure twice, and you may get 21 mm one time and 22 mm the next. Your friend may get 23 mm.
None of you is careless. This is what measuring is really like. Every measurement is made with an instrument, and every instrument has a limit. Every reading is also made by a person, and people add their own small mistakes. The skill in this lecture is not "reading the number off the scale". It is choosing the right instrument, using it in the way that removes your own mistakes, and knowing how far you can trust what you read.
The smallest division sets the limit
Look closely at a ruler. The smallest marks are 1 mm apart. That one fact decides how finely the ruler can measure. A length of 12.63 cm falls between two marks, and you cannot tell whether it is 12.62 or 12.64. So with a ruler you read to the nearest millimetre: 12.6 cm.
The precision of an instrument is the smallest difference it can show. For a ruler it is 1 mm, the smallest division. Write every reading so that it shows this. A length of exactly 12 cm read on a ruler is written 12.0 cm, not 12 cm. The ".0" is not decoration. It says "I checked the millimetres, and there were none". Some courses also ask you to estimate half a millimetre; follow your own course, but never write more decimal places than you have really read.
Different jobs need different precision. A builder measuring a room with a tape measure does not need tenths of a millimetre. An engineer making a part for an engine may need hundredths. So the first question is always: how precise does this measurement need to be? Then choose the instrument.
Using a ruler properly
Three habits turn a ruler from a rough guide into a reliable instrument.
Start from a mark, not from the end. On many rulers, the 0 mark is a few millimetres in from the end. On an old ruler, the end is often worn or chipped. If you line the object up with the end, every reading is wrong by the same amount. The safest method is to line one end of the object up with a clear mark, such as 2.0 cm, read the other end, and subtract.
Look straight down. The marks on a ruler are on its top surface, but the object you measure is often a little above or below them. If your eye is off to one side, the line from your eye past the object's edge reaches the scale at the wrong place. This shift is called parallax.
Look at the picture. The corner is the same. Only the eye moves, and the reading changes by 0.4 cm either way, four times the ruler's precision. The cure costs nothing: put your eye directly above the point you are reading. This applies to every scale you will ever read, including thermometers and measuring cylinders.
Make awkward edges into straight ones. Back to the coin. Stand two blocks against it, one on each side, both square to the ruler. Now the coin's diameter is the gap between two flat faces, and flat faces are easy to read.
A student wants the thickness of one sheet of paper. Her ruler measures to 1 mm, and a sheet is much thinner than that. Is the ruler useless for this job?
Show the answer
No. Measure many sheets together, then divide. A pack of 500 sheets might be 52 mm thick. Then one sheet is 52 ÷ 500 = 0.104 mm, about 0.10 mm. The ruler is still only good to 1 mm. But that 1 mm is now shared between 500 sheets, so each sheet's share of the error is 1 ÷ 500 = 0.002 mm. Measuring many and dividing is one of the most useful tricks in physics. You will meet it again with the pendulum.
Finer than a millimetre: the vernier calliper
For small objects that need more precision, such as a coin, a bolt or the inside of a pipe, physicists use a vernier calliper. It has jaws that close on the object, a main scale marked in millimetres, and a small sliding scale called the vernier scale. With it you can read to 0.1 mm, ten times more precisely than a ruler.
How can a scale marked in millimetres show tenths of a millimetre? This is the clever part, so take it slowly. The vernier scale has 10 divisions, but they fit into 9 mm. So each vernier division is 0.9 mm, which is 0.1 mm shorter than a main-scale millimetre.
Suppose the jaws are open by 23.4 mm. The vernier's zero line sits 0.4 mm past the 23 mm mark. Vernier line 1 is 0.9 mm further on, so it is 0.3 mm past a main-scale mark. Line 2 is 0.2 mm past one, line 3 is 0.1 mm past one, and line 4 is exactly on one. The gap shrinks by 0.1 mm at every step, so the number of the line that lines up is the number of tenths. That is it. That is the whole idea of a vernier.
So reading a vernier takes two steps. First, read the main scale just before the vernier zero: 23 mm. Second, find the vernier line that lines up best with any main-scale line: line 4, so add 0.4 mm. The reading is 23.4 mm, or 2.34 cm. Try it below.
Slide the jaw with the slider or the − / + buttons (0.1 mm each step). For each position, read the scale yourself, then press Show the reading to check.
Jaw opening:
Try:
A vernier scale reading 23.4 mm. The vernier zero is just past 23 mm on the main scale, and vernier line 4 is the one that lines up exactly with a main-scale line (at 27 mm).
Notice two things. First, the matching line can be anywhere along the vernier; you do not need to know which main-scale mark it matches. Second, when the vernier zero lines up exactly with a main-scale mark, line 0 and line 10 both match, and the reading has 0 tenths, as at 7.0 mm. A vernier calliper should also read 0.0 mm when its jaws are closed. Check this before you start. A micrometer screw gauge goes ten times finer again, to 0.01 mm, using a screw that moves 0.5 mm for each turn; you will use one in later years.
Measuring mass
Mass is the amount of matter in an object. It is measured in grams (g) and kilograms (kg) with a balance.
A beam balance compares masses directly. The object goes on one side and known masses go on the other, until the beam is level. An electronic balance works differently. It measures how hard the object pushes down on it, and it is set up to show that push as a mass. On Earth this gives the right answer. Physics keeps "mass" (in kilograms) and "weight" (a force, in newtons) apart, and a later lecture explains why. So in physics we say "the mass is 125.5 g", not "it weighs 125.5 kg" or "its weight is 125.5 g".
Two habits matter with an electronic balance. Check that it reads 0.0 g with nothing on it, and press the zero (or "tare") button if it does not. Then wait until the reading stops changing before you record it. To find the mass of a liquid, use the tare button: put the empty beaker on, press tare so the display shows 0.0 g, then pour in the liquid. The display now shows the liquid alone.
Measuring time, and the problem of your own hand
A stopwatch shows time to 0.01 s. That looks very precise. But a person starts and stops it, and a person is much slower than the display. Human reaction time to something seen is usually about 0.15 to 0.3 s. When you time something you can see coming, such as a swinging pendulum, you can anticipate and do better, but each reading can still be off by about 0.2 s. So the display shows hundredths, while your hand is only good to about two tenths.
A pendulum's period is the time for one complete swing: out, and back to where it started. Suppose the true period is 1.70 s. If you time one swing, your reading could be anywhere from about 1.50 s to 1.90 s. Now time 20 swings instead. The total is about 34 s, and your hand is still off by up to about 0.2 s. But that error is now shared between 20 swings. Each swing's share is 0.2 ÷ 20 = 0.01 s, twenty times smaller than before. It is the paper trick again.
This pendulum's true period is 1.70 s. Each time you press a button, a model student times 1, 5 or 20 swings. Their stopwatch reading is off by up to 0.2 s either way, at random, because of reaction time. Press each button several times and compare the dots.
Five sample timings for each method (made by the same model: true period 1.70 s, each stopwatch reading off by up to 0.2 s). The more swings timed, the closer every period is to 1.70 s.
| Swings timed | Five stopwatch readings (s) | Periods found (s) | Spread |
|---|---|---|---|
| 1 | 1.63, 1.56, 1.76, 1.53, 1.71 | 1.63, 1.56, 1.76, 1.53, 1.71 | 0.23 s |
| 5 | 8.45, 8.32, 8.50, 8.31, 8.47 | 1.690, 1.664, 1.700, 1.662, 1.694 | 0.038 s |
| 20 | 33.83, 33.84, 33.97, 34.13, 33.85 | 1.692, 1.692, 1.698, 1.707, 1.693 | 0.015 s |
The dots for one swing are scattered widely. The dots for 20 swings sit almost on top of each other, close to 1.70 s. Every one of those timings had the same size of hand error. Timing more swings did not make the student faster; it made each error count for less. The model leaves things out: real hand errors are not all the same size, and a student can also lose count of the swings. The next topic, on errors in measurement, gives these kinds of mistakes their names.
1. Choose an instrument whose smallest division suits the job: ruler 1 mm, vernier calliper 0.1 mm, micrometer 0.01 mm.
2. Remove your own mistakes: start from a clear mark, check the zero, look straight at the scale.
3. When one item is too small or too quick to measure well, measure many together and divide.
4. Record every reading with its unit and with as many decimal places as you really read.
Worked examples
The end of a ruler is chipped, so a student lines the left end of a pencil up with the 2.0 cm mark. The right end is at 14.6 cm. Find the length in cm, mm and m.
Length = 14.6 cm − 2.0 cm = 12.6 cm.
In millimetres: 1 cm = 10 mm, and a smaller unit needs a bigger number, so 12.6 × 10 = 126 mm. In metres: 1 m = 100 cm, and a bigger unit needs a smaller number, so 12.6 ÷ 100 = 0.126 m.
Check. A pencil is shorter than a 15 cm ruler and much longer than a fingernail, so about 13 cm is sensible ✓.
A student times 20 complete swings of a pendulum and gets 34.0 s. Find the period. If her timing could be off by 0.2 s, how far off could the period be?
Period = total time ÷ number of swings = 34.0 s ÷ 20 = 1.70 s.
The 0.2 s is shared between 20 swings: 0.2 ÷ 20 = 0.01 s. So the period is 1.70 s, give or take about 0.01 s. Timing one swing, it could have been off by 0.2 s: twenty times worse.
Check. 1.70 × 20 = 34.0 ✓.
The vernier zero is just past the 18 mm mark, and vernier line 6 lines up with a main-scale line. What is the reading in mm and in cm?
Main scale: 18 mm. Vernier: line 6, so 6 × 0.1 mm = 0.6 mm. Reading = 18 + 0.6 = 18.6 mm. In centimetres, 18.6 ÷ 10 = 1.86 cm.
Check. Line 6 of the vernier is 6 × 0.9 = 5.4 mm beyond the vernier zero, so it sits at 18.6 + 5.4 = 24.0 mm, exactly on a main-scale mark ✓.
An empty beaker on a balance reads 52.3 g. With water in it, the balance reads 177.8 g. Find the mass of the water in g and in kg. How could the tare button make this quicker?
Mass of water = 177.8 g − 52.3 g = 125.5 g. In kilograms: 1 kg = 1000 g, so 125.5 ÷ 1000 = 0.1255 kg.
With the tare button: put the empty beaker on, press tare so the display shows 0.0 g, then pour in the water. The display shows 125.5 g directly, with no subtraction.
Check. 52.3 + 125.5 = 177.8 ✓.
The 0 mark is usually a little way in from the end, and ends wear down. Line the object up with a clear mark and subtract, or check that the end really is at 0.
An eye to one side moves the reading (parallax). Put your eye directly above, or level with, the point you read, every time.
If you say "one" as you start the stopwatch, you will stop after only 19 swings when you reach "twenty". Start the count at "zero" as the pendulum passes a marker, and stop on "twenty".
Work each one on paper first. Open a hint only when you are stuck.
-
One end of a key is at the 3.5 cm mark of a ruler and the other end is at 11.2 cm. Find its length in cm, mm and m.
Hint 1
Subtract the two readings.
Hint 2
Smaller unit, bigger number: × 10 for mm. Bigger unit, smaller number: ÷ 100 for m.
Full answer
11.2 − 3.5 = 7.7 cm. In mm: 7.7 × 10 = 77 mm. In m: 7.7 ÷ 100 = 0.077 m. Check: a key is a few centimetres long ✓.
-
(a) A vernier's zero is just past 41 mm and line 7 lines up. What is the reading? (b) Which instrument would you choose for: the length of a classroom; the diameter of a coin; the thickness of a thin wire? Give a reason for each.
Hint 1
Main scale first, then the tenths from the matching line.
Hint 2
Match the size of the job to the smallest division: tape measure (1 mm or 1 cm), vernier (0.1 mm), micrometer (0.01 mm).
Full answer
(a) 41 + 0.7 = 41.7 mm = 4.17 cm. (b) Classroom: a tape measure; a few metres, and 1 mm or 1 cm is plenty. Coin: a vernier calliper; about 2 cm across, and 0.1 mm gives a useful answer. Thin wire: a micrometer; it may be only a fraction of a millimetre, so even 0.1 mm is too coarse. Check: line 7 is 7 × 0.9 = 6.3 mm on, at 41.7 + 6.3 = 48.0 mm, exactly on a mark ✓.
-
Lin times 10 swings of a pendulum and gets 15.6 s. (a) Find the period. (b) Her timing could be off by 0.2 s. How far off could her period be? (c) How many swings must she time so that the period is off by no more than 0.01 s?
Hint 1
Period = total time ÷ number of swings.
Hint 2
The 0.2 s is shared between all the swings timed. What number of swings makes 0.2 ÷ n = 0.01?
Full answer
(a) 15.6 ÷ 10 = 1.56 s. (b) 0.2 ÷ 10 = 0.02 s. (c) 0.2 ÷ n = 0.01 gives n = 20 swings. Check: 1.56 × 10 = 15.6 ✓, and 0.2 ÷ 20 = 0.01 ✓.
-
A pack of 500 sheets of A4 paper is 5.0 cm thick and has a mass of 2.5 kg. An A4 sheet is 21.0 cm by 29.7 cm. (a) Find the thickness of one sheet in mm. (b) Find the mass of one sheet in g. (c) Paper is often described by its mass for each square metre. Find it for this paper.
Hint 1
Change to convenient units first: 5.0 cm = 50 mm, 2.5 kg = 2500 g.
Hint 2
One sheet's area in square metres is 0.210 m × 0.297 m. Divide one sheet's mass by its area.
Full answer
(a) 50 mm ÷ 500 = 0.10 mm. (b) 2500 g ÷ 500 = 5.0 g. (c) Area = 0.210 × 0.297 ≈ 0.0624 m². Mass per square metre = 5.0 ÷ 0.0624 ≈ 80 g/m². Office paper is often sold as "80 g/m²", so this matches. Check: 80 × 0.0624 ≈ 5.0 g ✓.
The vernier scale is almost four hundred years old. Pierre Vernier, a French mathematician, described it in a book published in Brussels in 1631. Its trick, comparing two scales that are slightly different so that a small difference shows up where they match, is still used in modern instruments.
The two ideas of this lecture, a better instrument and many measurements combined, have taken physics a very long way. In 2015, the LIGO detectors in the United States detected waves from two black holes colliding. To do it, they sensed changes in the length of tunnels 4 km long that were about ten thousand times smaller than the width of a proton. Reading a ruler with your eye directly above the scale is the first step on the same road.
- The precision of an instrument is the smallest difference it can show, set by its smallest division.
- A ruler reads to 1 mm, a vernier calliper to 0.1 mm and a micrometer screw gauge to 0.01 mm, so the instrument is chosen to suit the job.
- Parallax is the shift in a reading when the eye is not directly above the point being read.
- A vernier reading is the main-scale reading before the vernier zero plus 0.1 mm for each division up to the line that lines up.
- A balance measures mass in grams or kilograms, and it should read zero before use.
- Measuring many items or many swings together and dividing shares the error between them, so each one's share is smaller.