MathemagiciansLibraryExplorationsDeep Dives
← Physics · Lower Secondary
PhysicsLower Secondary

Physical quantities — measuring the world

LSP1.1 — Physical Quantities and UnitsLecture 1 of 2~2540 words

"The table is 5 long"

Suppose a friend tells you, "The table is 5 long." Five what? Five hand spans? Five steps? Five metres? Each answer gives a very different table. The number 5 on its own tells you nothing.

This sounds like a small problem. It is not. In 1999, NASA lost a spacecraft called the Mars Climate Orbiter. It had cost about 125 million US dollars, and it had travelled for nine months to reach Mars. On 23 September 1999, as it fired its engine to go into orbit, it flew far too close to the planet and was lost. The cause was a mix-up of units. One computer program gave the size of the spacecraft's small engine pushes in "pound-force seconds", an old British unit. The program that read those numbers expected "newton seconds", the international unit. One pound-force is about 4.45 newtons. So every push was taken to be about 4.45 times smaller than it really was, for months. The numbers were right. The units were not.

This lecture is about the agreement that stops that from happening: what a measurement really is, the units every scientist in the world shares, and how to move between them without mistakes.

A number and a unit

A physical quantity is anything in nature that can be measured: a length, a mass, a time, a temperature. Every measurement of a physical quantity has two parts. It has a number, and a unit.

The unit is an amount that everyone has agreed on. The number says how many of those amounts there are. So "5 m" means "5 times one metre". This is why the unit matters as much as the number. Change the unit and you change the meaning completely: 5 mm is the width of a pencil, and 5 km is a long walk.

A physical quantity

quantity = number × unit

Example: a length of 5 m means 5 × (one metre). A measurement without its unit is not a measurement. It is just a number.

Here is a consequence that surprises many students. The same length can be written with many different numbers. A textbook that is 24 mm thick is also 2.4 cm thick, and also 0.024 m thick. These are not three different lengths. They are one length, described with three different units. When the unit is bigger, you need fewer of them, so the number is smaller.

Units also have rules for how they are written. Put a space between the number and the unit: 5 m, not 5m. Never add an "s" for a plural: 5 kg, not 5 kgs. And small and capital letters matter. A small m is a metre, but a capital M means "million". So 5 mm and 5 Mm are a thousand million times apart.

The seven base quantities

Scientists in every country use one system of units. It is called the SI, from its French name, Système International d'Unités (International System of Units). It starts from seven base quantities. Each has a base unit.

Base quantitySI base unitSymbol
lengthmetrem
masskilogramkg
timeseconds
temperaturekelvinK
electric currentampereA
amount of substancemolemol
luminous intensity (brightness of a light source)candelacd

Why these seven? They were chosen by international agreement, partly for historical reasons. Nothing in nature forces exactly this list. But once they are agreed, every other unit can be built from them. At this level you will mostly use the first three: the metre, the kilogram and the second.

Look at the kilogram. It is the only base unit with a prefix ("kilo") already in its name. That is an accident of history, and you will meet the prefixes in a moment.

How does everyone make sure their metre is the same as everyone else's? Today each base unit is defined from a fixed constant of nature. The metre, for example, is defined by the speed of light. Since 20 May 2019, all seven units have been defined this way. Before that, the kilogram was the mass of one particular metal cylinder kept near Paris. A unit tied to nature can be checked anywhere in the world, by anyone with the right equipment.

Derived quantities: building new units

Most quantities in physics are not on the list. Speed, area, volume, density, force and energy are all missing. These are derived quantities. Each one is made by multiplying or dividing base quantities, and its unit is made the same way.

That is it. That is the whole idea of derived units: the unit follows the formula. If you know how a quantity is calculated, you can build its unit, and you never need to memorise it.

A few derived units are used so often that they have their own names. The unit of force is the newton (N), named after Isaac Newton. One newton is the same as one kg m/s². The unit of energy is the joule (J), named after James Joule. But most derived units have no special name. The metre per second is simply "metres per second". When a unit is named after a person, its symbol starts with a capital letter (N, J) but the name is written with a small letter (newton, joule).

Stop and think

A student writes the speed of a cyclist as "5 m/s²". Another writes "5 m/s". Is this only a small difference in how it is written?

Show the answer

No. They are units of two different quantities. Metres per second (m/s) is the unit of speed: how far you go each second. Metres per second squared (m/s²) is the unit of acceleration: how much your speed changes each second. A cyclist moving steadily at 5 m/s has an acceleration of 0 m/s². The little "²" changes the quantity completely, so write it, and read it, with care.

Prefixes: the same unit, bigger or smaller

Real measurements can be very large or very small. The distance from the Earth to the Moon is about 384 000 000 m. The width of a human hair is a tiny fraction of a metre. Writing long rows of zeros is slow, and it is easy to lose one. So the SI uses prefixes. A prefix is a word in front of a unit that multiplies it by a fixed number.

PrefixSymbolMultiplies byExample
kilok10001 km = 1000 m
centic0.01 (one hundredth)1 cm = 0.01 m
millim0.001 (one thousandth)1 mm = 0.001 m
microμ0.000 001 (one millionth)1 μm = 0.000 001 m

The symbol μ is the Greek letter "mu", said "mew". So "μm" is the micrometre. With powers of ten, kilo is 10³ and micro is 10⁻⁶.

A prefix works with any unit. A kilogram is 1000 grams. A millisecond is one thousandth of a second. A kilometre is 1000 metres. Once you know the prefix, you know the multiplier, whatever the unit.

Now, converting. Here is the one reason behind every conversion, so that you never have to memorise which way to go. A smaller unit fits more times into the same length, so the number gets bigger. A bigger unit fits fewer times, so the number gets smaller. The ladder below shows the steps between the length units you will use most.

× 1000÷ 1000× 100÷ 100× 10÷ 10× 1000÷ 1000kmmcmmmμmto a smaller unit: more of them, so multiplyto a bigger unit: fewer of them, so divide
Moving down the ladder to a smaller unit, multiply: 1 km = 1000 m = 100 000 cm. Moving up to a bigger unit, divide: 24 mm = 2.4 cm = 0.024 m.

Try it below. Choose an object, then show its length in different units. Watch the number change while the object stays exactly the same.

Explore — one length, five units

Choose an object. Then choose a unit. The grey bar is the object. The blue blocks show how many of that unit fit along it.

Object:

Unit:

Three objects, each written in five units. Down each column the length is the same; only the unit and the number change. (5 billion is 5 000 000 000.)

UnitTextbookHair5 km run
μm24 000705 billion
mm240.075 000 000
cm2.40.007500 000
m0.0240.000 075000
km0.000 0240.000 000 075

Notice that the textbook is a sensible size in millimetres or centimetres, the hair in micrometres, and the run in kilometres. Scientists choose the unit that gives a number that is easy to read. That is the whole purpose of prefixes.

Scalars and vectors

There is one more way to sort physical quantities. Some quantities have only a size. A mass of 3 kg, a time of 10 s and a temperature of 25 °C need nothing more. These are scalars.

Other quantities also have a direction, and the direction changes what happens. A push of 10 N to the right is different from a push of 10 N to the left. These are vectors. Force is a vector. So is velocity, which is speed in a stated direction: "20 m/s north" is a velocity, while "20 m/s" alone is a speed.

The difference matters most when you add them. Two scalars add like ordinary numbers: 3 kg of rice and 2 kg of rice make 5 kg. Two vectors add like arrows, so their directions count.

10 N10 NOpposite directions: total force 0 N10 N10 NSame direction: total force 20 N to the right
Each arrow is a force acting on the box. Top: two forces of 10 N act in opposite directions. The total force is 0 N, so the box does not start to move. Bottom: both forces act to the right. The total force is 20 N to the right.

The same two forces of 10 N can give a total of 0 N or 20 N. Only the directions are different. A number for a vector is not complete until you say which way it acts. You will add vectors in many later lectures, starting with forces.

Stop and think

On a cold morning the temperature is −5 °C. It has a minus sign. Does that make temperature a vector?

Show the answer

No. The minus sign means "5 degrees below zero" on the temperature scale. It does not point anywhere in space. Temperature has a size only, so it is a scalar. For a vector, a minus sign means something different: the opposite direction, such as "to the left" when right is positive. Always ask: does this quantity point somewhere? If not, it is a scalar.

Worked examples

Worked Example 1 — Converting with prefixes

A textbook is 24 mm thick. Write this in centimetres and in metres.

Think first. Centimetres and metres are both bigger than millimetres, so both numbers must be smaller than 24.

To centimetres. 1 cm = 10 mm, so divide by 10: 24 ÷ 10 = 2.4 cm.

To metres. 1 m = 1000 mm, so divide by 1000: 24 ÷ 1000 = 0.024 m.

Check. Both numbers are smaller, as expected ✓. And 2.4 cm = 0.024 m, because 2.4 ÷ 100 = 0.024 ✓.

Worked Example 2 — A speed in SI units

A car travels 180 km in 2 hours. Find its average speed in m/s.

Convert the distance. 180 km = 180 × 1000 m = 180 000 m.

Convert the time. 1 hour = 60 minutes = 60 × 60 s = 3600 s. So 2 hours = 7200 s.

Divide. speed = distance ÷ time = 180 000 m ÷ 7200 s = 25 m/s.

Check. In everyday units the car does 180 ÷ 2 = 90 km/h. Since 1 km/h = 1000 m ÷ 3600 s, dividing by 3.6 turns km/h into m/s: 90 ÷ 3.6 = 25 ✓. And 25 m/s is a sensible speed for a car on a fast road.

Converting time is where most mistakes in this kind of question happen. Find the mistake in the working below.

Spot the error — a speed conversion

Kiri works out the speed of the car in Worked Example 2. One line contains the mistake. Tap it.

Kiri's working, with the mistake marked.

  1. The distance is 180 km = 180 × 1000 m = 180 000 m. (Correct.)
  2. The time is 2 hours = 2 × 60 s = 120 s. (The mistake: 2 hours = 2 × 60 × 60 s = 7200 s.)
  3. Speed = 180 000 m ÷ 120 s. (Right method, wrong time.)
  4. Speed = 1500 m/s. (Far too fast for a car. The correct answer is 25 m/s.)
Worked Example 3 — Very small lengths

Human hairs vary a lot in thickness, from about 17 μm to about 181 μm. Take a hair that is 70 μm wide. (a) Write its width in millimetres. (b) About how many such hairs, side by side, would cover 1 mm?

(a) 1 mm = 1000 μm. A millimetre is the bigger unit, so divide: 70 ÷ 1000 = 0.07 mm.

(b) Each hair covers 0.07 mm. The number of hairs in 1 mm is 1 ÷ 0.07 ≈ 14.

Check. 14 × 70 μm = 980 μm, just under 1000 μm = 1 mm ✓.

Worked Example 4 — Scalar or vector, and adding forces

(a) Sort these into scalars and vectors: mass, force, time, velocity, temperature, speed. (b) Two forces act on a box: 30 N to the right and 20 N to the left. What is the total force?

(a) Ask of each one: does it point somewhere? Scalars: mass, time, temperature, speed. Vectors: force, velocity.

(b) The forces point in opposite directions, so they partly cancel. Total = 30 N − 20 N = 10 N, in the direction of the larger force: 10 N to the right.

Check. If both forces pointed to the right, the total would be 50 N. Opposite directions must give less than that, and 10 N is less ✓.

Trap 1 — A number without its unit

Writing "the length is 24" loses marks and can cause real disasters. Write the unit with every measurement and every answer. Before you combine two numbers, make sure they are in the same units.

Trap 2 — Converting the wrong way

Changing 24 mm into metres by multiplying gives 24 000 m: a textbook 24 km thick. Always ask, "Is my new unit bigger or smaller?" Bigger unit, smaller number. Smaller unit, bigger number.

Trap 3 — Small letters and capital letters

m is a metre and M means million. k (kilo) is small, and K is the kelvin. m/s is a speed and m/s² is an acceleration. Copy the symbols exactly.

Try it yourself

Work each one on paper first. Open a hint only when you are stuck.

  1. Convert: (a) 3.5 km into metres; (b) 450 g into kilograms; (c) 2.5 minutes into seconds.

    Hint 1

    For each one, decide whether the new unit is bigger or smaller than the old one.

    Hint 2

    1 km = 1000 m, 1 kg = 1000 g, 1 minute = 60 s.

    Full answer

    (a) Metres are smaller, so multiply: 3.5 × 1000 = 3500 m. (b) Kilograms are bigger, so divide: 450 ÷ 1000 = 0.45 kg. (c) Seconds are smaller, so multiply: 2.5 × 60 = 150 s. Check: in (a) and (c) the number grew, and in (b) it shrank ✓.

  2. A cyclist rides 6 km in 20 minutes. Find the average speed in m/s.

    Hint 1

    Change the distance into metres and the time into seconds first.

    Hint 2

    6 km = 6000 m and 20 minutes = 20 × 60 s.

    Full answer

    Distance = 6000 m. Time = 20 × 60 = 1200 s. Speed = 6000 ÷ 1200 = 5 m/s. Check: 6 km in a third of an hour is 18 km/h, and 18 ÷ 3.6 = 5 ✓.

  3. (a) Which of these are vectors: distance, force, energy, velocity, mass? (b) A boat is pushed by a wind force of 15 N to the east and a current force of 9 N to the west. Find the total force.

    Hint 1

    For each quantity, ask whether it points somewhere.

    Hint 2

    Opposite directions: subtract, and take the direction of the larger force.

    Full answer

    (a) Force and velocity are vectors. Distance, energy and mass are scalars. (b) Total = 15 − 9 = 6 N to the east. Check: the total lies between 0 N and 15 + 9 = 24 N, and it points the same way as the larger force ✓.

  4. Think about the Mars Climate Orbiter. One program measured a small engine push as 10 pound-force seconds and passed on the number 10. The other program read it as 10 newton seconds. One pound-force is about 4.45 newtons. (a) How big was the push really, in newton seconds? (b) By what factor did the second program underestimate it? (c) Why did this error, small for one push, become serious?

    Hint 1

    10 pound-force seconds means 10 × (one pound-force) × (one second). Replace one pound-force with 4.45 newtons.

    Hint 2

    Compare the real value with the value the program believed.

    Full answer

    (a) 10 × 4.45 = 44.5 newton seconds. (b) The program believed 10 instead of 44.5, so it underestimated every push by a factor of 44.5 ÷ 10 = 4.45. (c) The spacecraft made many small pushes on its long journey, and each one was taken to be too small. The errors added up over months, so its path ended up far from where the team thought it was. Check: the factor is the same for every push, because it comes from the units, not from the size of the push ✓.

The bigger idea

Measurement is an agreement between people. When the metric system began in France in the 1790s, the metre was based on the size of the Earth itself. Over two centuries the definitions have been made more and more exact, and today every SI unit is tied to a constant of nature. A scientist in Chennai, an engineer in Singapore and a student in Barbados can all make the same metre without ever sending each other a ruler.

Every lecture in physics from here on uses this language. Each time you meet a new quantity, ask two questions. What is it measured in? And does it have a direction? Those two questions catch more mistakes than any formula.

Key concepts in this lesson